Roof Trims

Fitted to roof edge to allow drainage into gutter.

Girth: 200mm Depth: 90mm Length: 3 metres

Fitted to roof edge to allow drainage into gutter.

Girth: 200mm Depth: 90mm Length: 3 metres

Deep Drip Facia used to cover insulation and allow maximum gutter penatration

Girth: 250mm Depth: 140mm Length: 3 metres

Deep Drip Facia used to cover insulation and allow maximum gutter penatration

Girth: 250mm Depth: 140mm Length: 3 metres

Fitted to roof edge to prevent water run off.

Girth: 230mm Depth: 105mm Length: 3 metres

Fitted to roof edge to prevent water run off.

Girth: 230mm Depth: 105mm Length: 3 metres

Fitted to roof edge to prevent water run off. Deeper face than B230 to allow for added external insulation.

Girth: 260mm Depth: 125mm Length: 3 metres

Fitted to roof edge to prevent water run off. Deeper face than B230 to allow for added external insulation.

Girth: 260mm Depth: 125mm Length: 3 metres

Replaces traditional lead flashing and used for driving into brickwork where flatroof butts against existing wall. Overlaps section D.

Vertical Cover: 100mm Wall Penetration: 35mm Length: 3 metres

Replaces traditional lead flashing and used for driving into brickwork where flatroof butts against existing wall. Overlaps section D.

Vertical Cover: 100mm Wall Penetration: 35mm Length: 3 metres

For use where flatroof butts against existing wall and creates a 45deg. angle to deflect rainwater from existing 90deg. angle. Fits under section C.

Flanges 80mm & 105mm Height 120mm, Girth 260mm Length: 3 metres

For use where flatroof butts against existing wall and creates a 45deg. angle to deflect rainwater from existing 90deg. angle. Fits under section C.

Flanges 80mm & 105mm, Height 120mm, Girth 260mm. Length: 3 metres

Omega shaped section for use on large areas. May also be used to control drainage.

Girth: 280mm Flanges: 90mm Height:50mm Length: 3 metres

Omega shaped section for use on large areas. May also be used to control drainage.

Girth: 280mm Flanges: 90mm Height:50mm Length: 3 metres

For use with section A & B to provide a neat finish to both right & left external corners. NB Must be used with the B260 Upstands

For use with section A & B to provide a neat finish to both right & left external corners. NB Must be used with the B260 Upstands

For use with sections D260 & or A200/B260 to Provides pre-formed left hand corners.

For use with sections D260 & or A200/B260 to Provides pre-formed left hand corners.

For use with sections D260 & or A200/B260 to Provides pre-formed right hand corners.

For use with sections D260 & or A200/B260 to Provides pre-formed right hand corners.

Pre-formed internal corner for D260 fillet trim, avoids the needs to mitre.

Pre-formed internal corner for D260 fillet trim, avoids the needs to mitre.

Pre-formed external corner for D260 fillet trim, avoids the needs to mitre.

Pre-formed external corner for D260 fillet trim, avoids the needs to mitre.

For use with section A200 & B260 to provide a neat finish to both right & left internal corners.

For use with section A200 & B260 to provide a neat finish to both right & left internal corners.

Used to simulate the appearance of raised rolled lead joints, also provides expansion.

Girth 130mm, flanges 20mm, height 40mm. Roll width 35mm Length: 3 metres

Used to simulate the appearance of raised rolled lead joints, also provides expansion.

Girth 130mm, flanges 20mm, height 40mm. Roll width 35mm. Length: 3 metres

A 300mm wide roll of 1mm thick flexible GRP sheet inserted under a pitched roof and brought down onto the flatroof. Price per m. Enter number of m required in Shopping Cart.

A 20m x 305mm wide roll of 1mm thick flexible GRP sheet inserted under a pitched roof and brought down onto the flatroof. Price per roll. Enter number of rolls required.

A 915mm wide roll of 1mm thick flexible GRP sheet inserted under a pitched roof and brought down onto the flatroof. Price per m. Enter number of m required in Shopping Cart.

A 20m x 915mm wide roll of 1mm thick flexible GRP sheet inserted under a pitched roof and brought down onto the flatroof. Price per roll. Enter number of rolls required.

Facia trim for concrete roofing or similar applications.

Girth 450mm: Depth 225mm. Length: 3 metres

Used on larger roofs to aid drainage and ensure gapping of underlying timber to facilitate expansion.

Girth 180mm: Flanges 30mm: Depth 15mm: Trough width 80mm. Length: 3 metres

Adhesion on inner face for forming upstands, gutters, floors, etc.

Girth 195mm: Flange widths 105mm and 85mm. Length: 3 metres

Adhesion on inner face for forming upstands, gutters, floors, etc.

Girth 195mm: Flange widths 105mm and 85mm. Length: 3 metres

Adhesion on outer face for step details, cover flashings etc.

Girth 195mm: Flange widths 105mm and 85mm. Length: 3 metres

Adhesion on outer face for step details, cover flashings etc.

Girth 195mm: Flange widths 105mm and 85mm. Length: 3 metres