Roof Trims

A complete range of GRP preformed roof trims and sections suitable for all liquid applied polymeric and single membrane systems. Our unique high adhesion finish gives excellent adhesion to most liquid applied systems without the need for priming. (Tested with both rigid and flexible polyester, polyurethane, acrylic and alkyd systems.)

Suitable for flat roofing, pitched roofing, cladding, domestic and industrial applications.

Consistent Weight and Thickness
Three Metre Lengths
Choice of Laminate Weight and Thickness
Excellent Finished Appearance
Easily Jointed

Facilitates Roof Void Ventilation
Unique High Adhesion Finish
Fire Retardent (BS 476 Part 3)
Highly Flexible
U.V. Stabilized and Prepigmented

Section:	Code:	Description:	Application:
	A200	Drip Facia 200mm girth 90mm deep facia	Fitted to roof edge for drainage into gutter. All edge detailing where drainage is required.
	A250	Drip Facia 250mm girth 140mm deep facia	Roof edge detail to cover insulation. Deep facia to allow gutter penetration.
	B230	Raised edge trim Check kerb 230mm girth 105mm facia depth	Flat roof edge detail to prevent water run off.
	B260	Raised edge trim 260mm girth 125mm facia depth	Roof edge detail. Compatible with Universal external covers.
	C100	Simulated lead wall cover flashing 100mm vertical cover 35mm wall penetration	Replaces traditional lead flashing. With integral moisture trap return self secures into brickwork
	C100 std	Simulated lead wall cover flashing 100mm vertical cover 35mm wall penetration	As above but without integral moisture trap.
	D240	Wall fillet 240mm girth 90mm flanges 120mm upstand height	For use against abutting walls. Gutter lining. Provides expansion joint and cross roof ventilation.
		Expansion Joint 280mm girth 100mm flanges 50mm height	Expansion joint for use on large roof areas with rigid systems or to cover existing ex joints on refurb. May also be used to control roof drainage.
		Flat Flashing Up to 1350mm wide Rolls from 24m long 300mm standard width	Flat section for use as continuous flashing under slates at roof junction. Gutter lining.

Corners:

Section:	Code:	Description:	Application:
	C1	Universal external corner. Hot press moulded GRP pre formed corner.	For use with Sections A200 and B260. Provides preformed RH and LH corners.
	C2	Fillet to trim RH and LH mouldings.	For use at junction of flat roof and abutting wall. Compatible with sec. D240, A200, B260.
	C3	Fillet corners Internal and external.	Chimney corners. Compatible with D240 only.
	C4	Universal internal corner.	For use with A200 and B260.

Pitched Roofing:

Section:

Code:

Description:

Application:

Continuous eaves course

Colour slate grey. Non binding finish

For use in place of first eaves slate course to provide initial lap.

All trims finished in light grey with outer high adhesion finish unless otherwise stated. All sections cut to 3 metre length except F300 and CE300 which are available in min. 20 metre rolls.
S. Standard laminate weight.	450gm. per sq. metre (1.1mm thick)
H. Heavyweight laminate weight.	600gm. per sq. metre (1.4mm thick)

Back to main

Shopping Cart

Items:
Value:

View Cart ››

Special Offers1. International Toplac 750ml 2. 3M Vapour Respirator 4251 3. Duratec Polyester Surfacing PrimerBest Sellers1. 20kg pack General Purpose Resin 2. Acetone Cleaner 25 litre 3. 5kg pack Clear Gelcoat 4. 20kg pack Grey Topcoat 5. West Epoxy B Pack 6kg 6. Chopped Strand Mat 10kg Roll 450gmQuick Links 1. Fibreglass 2. Gelcoat 3. Glass Fibre 4. GRP 5. Polyester Resin 6. Epoxy Resin